- Dji Naza M Lite Software
- Dji Naza M Lite Manual
- Naza M Lite Manual
- Dji Naza M V2 Instructions
- Dji Naza Manual
- Dji Naza M Lite Software
- Dji Naza M Lite Manuale Italiano
©2014 DJI. All Rights Reserved.
Naza-M Lite user Manual v2.00. PDF Assistant Software & Driver. Naza-M Lite Assistant Software v1.00 (Stop distributing and updating). Download the Firmware via Assistant software; the software only supports Windows XP or above (32bit/64bit). Looking ahead, DJI will continue to provide the best tools and services for.
May 04, 2013 I flew today first time in manual mode! I'm sorry, that I haven't tried it before. It's awesome!!! Thx for the music: Song Niki Kofman - Maelstrom VIP. View and Download Dji NAZA-M quick start manual online. NAZA-M Controller pdf manual download. Controller dji 430 LITE ESC User Manual (32 pages) Controller dji A3 User Manual (39 pages) Controller dji datalink 3 User Manual (26 pages) Controller dji phantom 2 User Manual. Flight controller (37 pages) Controller dji TAKYON Z14120 User. Important: Naza-M, Naza-M V2 and PHANTOM control system are different in hardware parts, but their configurations and functions are the same when using the same Assistant Software and Firmware Version, so they use the same Guide. Unless stated, the following instruction is basic on Naza-M V2. If you use the Naza-M, please. View and Download Dji Naza-M V2 quick start manual online. Compact Designed Multirotor Autopilot System Flight Controller GPS for copters. Naza-M V2 Controller pdf manual download. Also for: Naza-m. Mar 24, 2018 I bought Naza-M Lite. Before that i bought all other components from Hobbyking, that is drone frame, motors, ESCs, remote control etc. I have assembled everything together, went through the manual. I have configured my Remote Control with NAZA-M LITE app, everything looks ok there. Also have done the IMU calibration.
8
Assembly
接电调
Dji Naza M Lite Software
接云台
F1
F2
接电调
接云台
VU
Dji Naza M Lite Manual
·
Do not mount it on any other electronic devices. Make sure You can see the
LED light during the flight.
·
If use with DJI multi-rotor, you can solder the VU power cable to power
pads on frame bottom board. Please refer to DJI multi-rotor manual for
details.
·
If use with 3
rd
part multi-rotor, you can make a connecter by yourself to
connect VU, ESCs and battery.
·
Sufficient air flow over the VU is highly recommended.
MC
·
Please use
3M gummed paper provided To mount MC, and mount MC parallel to the
aircraft horizon.
·
The output ports of MC (the right side in figure) should point to the front of
multi-rotor. You
’d better put MC at the gravity center of multi-rotor. Please
make sure all ports are accessible when installing the MC so as to facilitate
wiring and software configuration.
·
In three-pin ports, pins near the nicks are signal pins.
·
After choosing a location to mount the MC, it is recommended
that you DO NOT mount the MC until all wirings and software configurations
are completed.
GPS/COMPASS
·
GPS/Compass is sensitive to magnetic interference, should be far away from any electronic
devices.
·
You should use epoxy resin AB glue to assemble the GPS bracket first as the figure showed
in previous page.
·
Mount the bracket on the center plate of craft first, then fix the GPS on the plate of the
bracket (by 3M glue provided). The GPS is sensitive to vibration interference, so position
the bracket at least 10 cm from any rotor.
·
Naza M Lite Manual
The DJI logo marked on the GPS should face the sky, with the orientation arrow pointing
directly forward. The GPS/Compass is packaged with a special indication line for mounting
for the first time.
·
If you are uncertain whether materials near the GPS/Compass module are magnetic or not,
you can use a compass or magnet to check it. If you use your own mounting rod, make sure
it is NOT magnetic!
Aircraft Nose
R/C System
These are example connections. Please
setup Aileron, Elevator, Throttle, Rudder
channels on your TX first, and choose
o n e 2 positions switch/channel ( 3
positions switch with GPS) as control
mode switch, then connect your receiver
to the right ports on MC.
R/C Receiver
(JR)
RUDD
THRO
AILE
ELEV
R/C Receiver
(Futaba / Hitec)
1
2
3
4
Futaba S-Bus
S-Bus
2/3-position switch channel
Optional
ESC
M1-6
To Battery
ESCs, Motors
·
Motors and ESCs in DJI multi-rotor kit are recommended.
·
Please make sure you are using the ESCs and motors recommended by the
manufacturer of your multi rotor first. NAZA-M LITE output is 400Hz
refresh frequency.
·
Connect all ESCs to MC by the motor numbering method introduced in
Multi-Rotors Supported of Appendix.
·
If you use 3
rd
party ESCs, please make sure the ESCs travel midpoint is at
1520us. DO NOT use 700us travel midpoint ESC, as it may lead aircraft to
fly away or cause injury and damage. After connect ESCs to motors,
calibrate all your ESCs one by one through the receiver directly before
connect them to your MC, Make sure program all of them into Governor off,
Break off and Normal Start up to get best experience.
Roll
Pitch
2/3-position switch channel
Dji Naza M V2 Instructions
Important: the continuous
output of the V U is 3A@5V, and the
maximum instant current is 7.5A. If the V U
cannot afford the working current for you r
servos, please use an independent power
supply; otherwise, it may cause the V U
safeguard and lead to the main controller
reboot.